Pengembangan Media Pembelajaran Trainer Sistem Pengisian Menggunakan Beban

Authors

Rizky Ferdiansyah Universitas Negeri Surabaya
A Grummy Wailanduw Universitas Negeri Surabaya

Keywords:

Pengembangan Media, Trainer, Sistem Pengisian

Abstract

Based on observations made by researchers in the undergraduate study program Mechanical Engineering Education, Surabaya State University, there are several obstacles faced, namely in the learning media trainer currently used in the Automotive Electrical Practices course, especially in the material of the charging system which only focuses on the charging system, so that students have difficulty in understanding the charging system material which is the same as the real conditions in the car. The purpose of this research is to develop learning media in the form of charging system trainer using a load with certain procedures that are in accordance with the objectives to be achieved. This research method is using the 4D development model. The subjects of this study were undergraduate students of Engineering Education Mechanical Engineering concentration of automotive class 2023 with a total of 5 students. Data collection in the form of a validation questionnaire sheet trainer and student response questionnaire sheet. The data analysis carried out is the analysis of trainer validation, and the analysis of student responses. The results of this study are in the form learning media for charging system trainers using loads that have been validated and declared suitable for use for learning with a validation score of 3.88 which is included in the Very Valid category. The results of student responsesto the charging system trainer media using the load are stated to be Very Good which obtained a score of 3.88, so it can be stated that the media is very good.

Downloads

Download data is not yet available.

References

1. Handoyono, N. A., & Rabiman (2023). ”Pengembangan Training Kit Engine Management System Toyota Avanza K3-VE Untuk Praktikum Otomotif”. Jurnal Pendidikan Vokasi Otomotif. Vol. 6 (1): pp 37-48. Yogyakarta : Universitas Sarjanawiyata Tamansiswa Yogyakarta.

2. Junaedi, I. (2019). “Proses Pembelajaran Yang Efektif”. Journal of Information System, Applied, Management, Accounting and Research. Vol. 3 (2): pp 19-25. Jayakarta: Sekolah Tinggi Informatika & Komputer Jayakarta.

3. Laksono, R. I. E. (2023). “Pengembangan Media Pembelajaran Sistem Rem Berbasis Prototype Untuk Meningkatkan Minat Belajar Siswa Kelas XI Teknik Kendaraan Ringan SMK Negeri 1 Sambeng Lamongan”. Jurnal Pendidikan Teknik Mesin. Vol. 12 (3): pp 39-44. Surabaya: Universitas Negeri Surabaya.

4. Prasetyoadi, A. Y. (2023). “Pengembangan Media Pembelajaran Trainer Sistem Pengapian CDI Sepeda Motor Pada Kompetensi Dasar Memperbaiki Sostem Pengapian Di Sepeda Motor”. Jurnal Pendidikan Teknik Mesin. Vol. 12 (1): pp 70-77. Surabaya: Universitas Negeri Surabaya.

5. Prasetyo, D. (2019).“Pengembangan Media Peraga Pada Kompetensi Mengidentifikasi Sistem Intermitten Wiper”. Jurnal Pendidikan Teknik Mesin. Vol. 19 (1): pp 13-18. Semarang : Universitas Negeri Semarang.

6. Setyanto, B. N., Budiastuti, P., Rismarinandyo, M. Y., & Yulanda, R. F., (2023). “Pengembangan Alat Peraga Sepeda Listrik Portable Sebagai Media Pembelajaran Elektronika Daya”. Jurnal Pendidikan Teknik Elektro. Vol. 8 (1): pp 39-46. Yogyakarta : Universitas Ahmad Dahlan.

7. Simanjuntak, R., Sinaga, N., & Pinem, M. W. E. (2023). “Pengembangan Trainer Air Conditioner Untuk Pembelajaran Siswa Kelan XI Teknik Pendinginan Tata Udara SMK Negeri 1 Percut Sei Tuan”. Jurnal Review Pendidikan dan Pengajaran. Vol 6 (2): pp 2079-2087. Medan : Universitas Negeri Medan.

8. Sugiono. (2013).”Statistika Untuk Penelitian”. Bandung : Alfabeta.

9. Sukiman, (2012). Pengembangan Media Pembelajaran. Yogyakarta : Pustaka Insan Madani.

10. Widoyoko, E. P., (2015). “Penilaian Hasil Pembelajaran di Sekolah”. Yogyakarta : Pustaka Belajar.

11. Yahya, M., Saharuna., & Wahyudi. (2023A). “Pengembangan Media Trainer CRC ECU Digital Diesel Injector Common Rail Berbasis Mikrokontroler”. Journal of Multidisciplinary Electrical & Eelectronics Engineering. Vol 1 (2): pp 20-26. Makasar : Universitas Negeri Makasar.

12. Yahya, M., & Wahyudi. (2023B). “Pengembangan Media Sistem Kerja Hall Sensor Pada Motor Kendaraan Listrik BLDC”. Jurnal Media Elektrik. Vol. 20 (2): pp 26-31. Makasar : Universitas Negeri Makasar.

13. Yulanto, D. M., Iskandar, H., & Rohmantoro, D. (2023). Pengembangan Media Pembelajaran Trainer Transmisi Manual Sepeda Motor”. Jurnal Teknologi Pembelajaran Indonesia. Vol. 13 (1): pp 56-68. Bantul: Universitas PGRI Yogyakarta.