STUDI PENGARUH TEBAL PELAT TERHADAP LENDUTAN PELAT MENERUS DITINJAU DARI FUNGSI BANGUNAN

  • WAHZUDI

Abstract

Lendutan merupakan faktor yang sangat penting dalam perencanaan sebuah struktur pelat, tetapi lendutan seringkali diabaikan, pada tabel 8 SNI 03-2847-2002 terdapat tebal pelat minimum untuk pelat satu arah jika lendutan tidak dihitung, dan pada tabel 9 SNI 03-2847-2002 terdapat batas lendutan ijin maksimum, penelitian ini bertujuan untuk mengetahui pengaruh tebal pelat (h) terhadap lendutan pelat dan melakukan peninjauan terhadap fungsi bangunan (beban hidup) serta bertujuan untuk mengetahui batas lendutan ijin maksimum pada tabel 9 SNI 03-2847-2002 dapat diterapkan pada perhitungan lendutan pelat menerus satu arah.

Jenis metode penelitian ini merupakan metode eksperimen-simulasi komputasi.  penelitian ini dilakukan dengan cara membuat beberapa model simulasi pada komputer dengan model pelat menerus satu arah dengan tumpuan sendi. Kemudian model penelitian tersebut diberi perlakuan untuk mengamati pengaruh ketebalan pelat (h), dengan variasi tebal pelat mulai dari tebal 90 mm sampai 170 mm. Pada penelitian ini penulis meneliti optimalisasi tebal pelat (h) berdasarkan fungsi  bangunan yang akan mempengaruhi beban hidup (QLL), fungsi bangunan yang digunakan yaitu: sebagai rumah tinggal sederhana dengan QLL=125kg/m2, perkantoran dengan QLL=250kg/m2, perpustakaan dengan QLL=400kg/m2, dan sebagai auditorium QLL=500kg/m2.

Hasil penelitian menunjukkan bahwa perubahan lendutan seketika yang terjadi semakin berkurang akibat perubahan dimensi tebal pelat dari 90 mm sampai dengan 170 mm, prosentase penurunan lendutan seketika adalah 15% - 75%, sedangkan prosentase penurunan lendutan jangka panjang berkisar antara  15% - 72%. Selisih antara lendutan seketika dan lendutan jangka panjang berkisar antara 44% - 47% dengan menggunakan faktor ketergantungan waktu ξ sebesar 2,0 untuk jangka waktu lebih dari 5 tahun. Perubahan lendutan seketika dan jangka panjang akibat QLLyang diterima oleh pelat relatif kecil dimana QLL sebesar 125 kg/m2, 250 kg/m2, 400 kg/m2, dan 500 kg/m2, kenaikan lendutan seketika berkisar antara 25% - 146%, sedangkan pada lendutan jangka panjang adalah 25% - 146%. Penelitian ini menghasilkan menghasilkan tebal yang optimal  untuk rumah tinggal sederhana = 110mm, perkantoran = 120mm, perpustakaan = 140mm dan auditorium = 150mm.

Kata Kunci : Pelat menerus satu arah,  Lendutan, Beban hidup

ABSTRACT

Deflection is a very important factor in planning a slab structure, but often overlooked deflection, deflection is a function of the stiffness that is multiplying the elastic modulus of concrete (Ec) with a inertia (I). In Table 8 SNI 03-2847-2002 there is a minimum slab thickness of the one way slab if the deflection is not counted, and on the table 9 SNI 03-2847-2002 there are permit maximum deflection limit. This study aimed to determine the effect of slab thickness (h) of the deflection slabs and a review of the functions of the building (live load) and aims to determine the maximum permit limit deflection in table 9 SNI 03-2847-2002 can be applied to the calculation of the deflection plates constantly one way.

This type of research method is a method of experimental-computational simulation. This study is done in a way to make some models in computer simulations with the model of continuous one-way slab with pedestal joints. Later models of the study were given treatment to observe the effect of plate thickness (h), with a thickness variation of the plate thickness ranging from 90 mm ​​to 170 mm. In this study the authors examined the optimization of plate thickness (h) based on the function of the building which will affect the live load (QLL), the function of the building that are used are: a simple dwelling house with QLL=125kg/m2, office with QLL=250kg/m2, library with QLL=400kg/m2, and the auditorium QLL=500kg/m2.

The results showed that the instantly deflection changes that occur on the wane due to changes in slab thickness dimensions of 90 mm ​​up to 170 mm, the percentage decrease in instantly deflection is 15% - 75%, while the percentage decline in the long-term deflection ranged between 15% - 72%. The difference between the instantly deflection and long term deflections ranged between 44% - 47% by using the time dependence of ξ factor of 2.0 for a period of more than 5 years. Changes instantly and long-term deflection due QLL received by slab  are relatively small where QLL for 125 kg/m2, 250 kg/m2, 400 kg/m2 and 500 kg/m2, the increase in instantly deflection ranged between 25% - 146%, while on the long-term deflection is 25% - 146%. This research resulted in produce an optimal thickness for simple residential = 110mm, 120mm = office, library = 140mm and auditorium = 150mm.

Key word:  Continuous one way slab, Deflection, Live load.

Published
2014-03-20
Abstract Views: 56
PDF Downloads: 928