ANALISIS PENGARUH KARAKTERISTIK SUMBER BAHAN BAKU AGREGAT PASIR KERTOSONO DAN AGREGAT KERIKIL MOJOKERTO TERHADAP KUAT TEKAN, KUAT TARIK (SPLIT CYLINDER) DAN MODULUS ELASTISITAS BETON MUTU TINGGI

  • FITRI PANCAR SUCI

Abstract

     Pemilihan agregat halus dan agregat kasar diambil dari beberapa daerah di Jawa Timur yaitu di kabupaten Kertosono untuk agregat halus dan Mojokerto untuk agregat kasar. Bahan dasar agregat bisa berupa material sungai maupun material gunung. Agregat merupakan salah satu bahan pengisi pada beton yang menempati 70-75% dari total volume beton, selain sebagai bahan pengisi agregat berkonstribusi positif pada sifat beton. Beton mutu tinggi (high strength concrete) didefinisikan sebagai beton yang mempunyai kuat tekan yang disyaratkan lebih besar sama dengan 41,4 MPa.

    Penelitian menggunakan beton mutu tinggi K400, K450 dan K500. Benda uji berbentuk silinder beton 15cmx30cm sebanyak 33 buah, dimana 5 buah untuk uji kuat tekan, 3 untuk uji kuat tarik belah dan 3 untuk modulus elastisitas pengujian dilakukan setelah benda uji berumur 28 hari. Karakteristik material dapat mempengaruhi kuat tekan, kuat tarik belah dan modulus elastisita beton, maka dilakukan pengujian karakteristik agregat halus dan kasar.

    Hasil pengujian karakteristik agregat dan benda uji beton menunjukan bahwa karakteristik Pasir Kertosono dan Kerikil Mojokerto memenuhi karakteristik material beton mutu tinggi setelah dicuci. Nilai kuat tekan rata-rata beton K400, K450 dan K500 yang dihasilkan mencapai 41,8 MPa, 46,6 MPa dan 51,4 MPa, nilai kuat tarik belah rata-rata beton K400, K450 dan K500 mencapai 3,11 MPa, 3,16 MPa, dan 3,25 MPa dan nilai rata-rata modulus elastisitas beton K400, K450 dan K500 mencapai 5063,8 MPa, 5617,3 MPa, 5353,9 MPa. Tetapi nilai regangan yang diperoleh belum memenuhi syarat regangan dengan metode Popovics (yang didapat 0,0083 dan yang seharusnya 0,0023).

Kata Kunci: Pasir Kertosono, Kerikil Mojokerto, Beton Mutu Tinggi, Karakteristik, Kuat Tekan, Kuat Tarik Belah, Modulus Elastisitas

Selection of fine aggregate and coarse aggregate taken from several areas in East Java is in Kertosono for fine aggregate and Mojokerto for coarse aggregate. Aggregate base material can be any streams material or mountain material. Aggregate is a filler material in concrete that occupies 70-75 % of the total volume of concrete , than as filler an aggregate contribute positively to the concrete nature. High strength concrete is defined as concrete that has a compressive strength greater required is equal to 41.4 MPa.

Research using high strength concrete K400, K450 and K500. Concrete cylindrical test specimens as many 33 pieces 15cmx30cm, where 5 pieces for compressive strength test, 3 pieces for split cylinder test anda 3 for modulus elasticity testing was conducted after the age of 28 days. Material characteristics can affect the compressive strength , split cylinder and modulus elasticity concrete then do the test characteristics of fine and coarse aggregate .

The results of testing the characteristics aggregate and concrete specimen showed that the characteristics Kertosono Sand and Mojokerto Gravel if qualified the characteristics of high strength concrete material after washing . Value of the average compressive strength of concrete K40 , K450 and K500 poduced by 41.8 MPa , 46.6 MPa and 51.4 MPa, value of the average split cylinder of concrete K400 , K450 and K500 produced by 3,11 MPa , 3,16 MPa , and 3,25 MPa , and value of the average  modulus elasticity of concrete K400 , K450 and K500 produced by 5063,8 MPa , 5617,3 MPa , 5353,9 MPa. But the strain values ​​obtained with the strain has not qualified Popovics method (which is supposed to come by 0.0083 and 0.0023).

Keywords: Kertosono Sand, Mojokerto Gravel, High Strength Concret, Characteristic, Compressive Strength, Split Cylinder, Modulus Elasticity

Published
2014-05-13
Abstract Views: 48
PDF Downloads: 330