ELEKTRODA PASTA KARBON TERMODIFIKASI KITOSAN UNTUKANALISIS LOGAM Fe(II) SECARA SIKLIK STRIPPING VOLTAMETRIDENGAN ION PENGGANGGU Zn(II) DAN Cd(II)CARBON PASTE ELECTRODE MODIFIED BY CHITOSAN FOR ANALYSISFe(II) USING CYCLIC STRIPPING VOLTAMETRY WITH INTERFERENCEION Zn(II) AND Cd(II)

  • CANDRA ADJIATMA PUTRA

Abstract

Abstrak. Telah dilakukan Modifikasi elektroda pasta karbon dengan menggunakan kitosan untuk analisis
ion Fe2+ secara siklik stripping voltametri dengan ion pengganggu Zn(II) dan Cd(II). Elektroda pasta
karbon termodifikasi kitosan dibuat dengan cara mencampurkan karbon aktif, parafin dan kitosan
dengan perbandingan 3:4:3, 3:3:4, 3:5:2 dan 3:2:5. Campuran ini dimasukkan kedalam pipa pvc dengan
diameter 2 mm dan dihubungkan dengan kawat tembaga sepanjang 12 cm. Setiap elektroda tersebut
diujikan pada larutan Fe(II) untuk ditentukan komposisi elektroda terbaik, kondisi optimum
elektroda(pH, kecepatan scan, dan waktu deposisi) serta pengaruh ion pengganggu Zn(II) dan Cd(II)
dalam analisis Fe(II). Dari hasil voltamogram menunjukkan elektroda dengan perbandingan 3:5:2
memberikan respon terbaik dengan arus puncak sebesar 8.447 x 10-6A pada daerah potensial 0,128V.
Hasil pengujian kondisi optimum elektroda pH optimum pada pH 3, waktu deposisi optimum 20 s dengan
arus puncak sebesar 9,204x 10-6 A pada daerah potensial 0,119 V dan kecepatan scan optimum sebesar
0,08 V/s. Keberadaan ion pengganggu Zn2+ ataupun Cd2+ sangat mempengaruhi proses analisis ion Fe2+
karena adanya ion pengganggu mampu meningkatkan besar arus puncak oksidasi.
Kata kunci : elektroda, kitosan, voltametri,besi(II),stripping
Abstract. modificationhave been made of carbon paste electrode by using chitosan for analyze ion Fe(II)
in a cyclic stripping voltammetry with interference ion Zn(II) and Cd(II). Carbon paste electrode
modified by chitosan was made by with mixing carbon active, paraffin oil, and chitosan with ratio 3:4:3,
3:3:4, 3:5:2, and 3:2:5. That mixture is fed into a pvc pipe with diameters 2 mm and conected with 12 cm
cooper wire. Each electrode is tested in solution of Fe(II) to determine the best ratio of electrode,
electrode optimum condition(pH, scan rate, and depotition time) as well as the effect of interference ion
Zn(II) and Cd(II) in analysis of Fe(II). From the results, voltamograms showed electrode with ratio 3:5:2
provide the best response with current peak 8,447 x 10-6A on potential area 0,128 V. The results of testing
the optimum conditions of pH optimum at pH electrode 3, the optimum deposition time of 20 s with a peak
current of 9,204x 10-6 A at 0.119 V and optimum scan speed of 0.08 V/s . The interference of ion Zn2+ or
Cd2+ greatly influence the Fe2+ ion analysis because of the large ion interference capable of increasing
the oxidation peak current.
Keywords : electrode, chitosan, Voltametry, iron(II), stripping

Published
2015-02-17
Abstract Views: 62
PDF Downloads: 74